Fits 2014-2009 Nissan Murano V6 3.5L DOHC Petrol Front Driver Side CV Axle Shaft

Description

Fitment: Nissan Murano 2009-2014 Position: Front Left Package Included: 1x CV Axle The role of CV Axle They are used to transfer power from the vehicle's transmission and differential to the wheels to propel the vehicle forward. They feature lubricated, flexible joints that allow the shaft to flex according to road conditions with minimal impact on power transmission. The joints are grease lubricated and covered with rubber boots to protect them from dust and dirt. How to change CV Axle ? Step1. First, make sure you have purchased a driveshaft that matches your car model. Fits 2014-2009 Nissan Murano V6 3.5L DOHC Petrol Front Driver Side CV Axle Shaft Fitment: Nissan Murano 2009-2014 Position: Front Left Package Included: 1x CV Axle The role of CV Axle They are used to transfer power from the vehicle's transmission and differential to the wheels to propel the vehicle forward. They feature lubricated, flexible joints that allow the shaft to flex according to road conditions with minimal impact on power transmission. The joints are grease lubricated and covered with rubber boots to protect them from dust and dirt. How to change CV Axle ? Step1. First, make sure you have purchased a driveshaft that matches your car model. Step2. Before starting, make sure your car's engine has cooled down and stopped running. Also, make sure your work area is tidy, spacious, and well-ventilated. Step3. Raise the car high enough off the ground so that you can easily access where the driveshaft is. This can be done by using a jack or car lift. Step4. Locate where the driveshaft is located, usually in the middle of the bottom of the car. It may have a protective cover that needs to be removed to access the driveshaft. Step5. Use a suitable tool (such as a wrench) to loosen the bolt or nut on the driveshaft and carefully remove the old driveshaft from the car. Step6. Clean the driveshaft socket and bearing housing to make sure no oil or other debris remains. Step7. Slide the new driveshaft into the socket on the underside of the car until it reaches the proper mounting position. Be careful not to push it in forcefully to avoid damaging the drive shaft or car parts. Step8. Use a wrench to tighten the bolt or nut on the drive shaft until it is fully seated. Step9. Check that the drive shaft is installed correctly and that it shows no signs of looseness or damage. Step10. Lower the vehicle back to the ground and perform a test drive to ensure the driveshaft is functioning properly. If there are any problems, please make adjustments in time. Item Specifics Brand hilamps Manufacturer Part Number 12490882 Manufacturer Warranty 1 Year Quantity 1 Fitment Type Direct Replacement Part Type CV Axle Assembly,CV Axle Shaft Surface Finish Painted Non-Domestic Product No Weight 20LB Bundle Listing No Placement on Vehicle Front Left Material steel Other Part Number 391011AA0A, 391011AA0C Superseded Part Number 66-6301 60-6301 NI-8352 NI-9530 Mounting Hardware Included No Input Shaft Connection Style Spline Number of Inboard Splines 29 Output Shaft Connection Style Spline Output Shaft Spline Count 32 Drive Type FWD ABS Ring Included No Axle Nut Locking Type Standard Spindle Nut Included Yes Modified Item NO Vintage Part NO Universal Part NO Payment 1.We accept any payment which can be accepted by eBay. 2.Please do check the shipping address. If you want to change the shipping address, please contact us by eBay messages. 3.If you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement. 4.Payment must be received within 10 days as auction ended or order might be delayed. Shipping 1. Orders processed within 24 hours of payment verification. (if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 2. The images shown are not the actual item and are for your reference only. 3. Fast shipping: All our packages use USPS First Class/UPS/Fedex... Package Service 4. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction! Returns 1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! 2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable. 3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. 4. Return shipping is to be paid by the Buyer. Feedback 1. We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. 2. It is impossible to address issues if we do not know about them! Shop Category Store Home Towing Mirrors Sensors Cooling System ◈ Radiator ◈ Cooling Fan ◈ Thermostat Housing ◈ Water Pump Air Conditioning System ◈ Condenser ◈ Module & Resistor ◈ Blower Lamps ◈ Brake light ◈ Instrument Light ◈ Headlight Assembly ◈ Side Marker light ◈ Headlight Truck Bed Accessories CV Axle Shaft Alternator Coolant Overflow Tank Brake pads Steering Shaft Windshield Wiper Motor Strut Assemblies Door Handle Wheel Hub Bearing Assembly Wheel Adapters Window Switch Bumpers Window Regulator Compressor Window Visor Drive shaft CDI BOX Other Hot Item 10X White T5 74 73 Bulb Led Gauge Dash Instrument Panel Light 5630 SMD 17 18 70 USD 8.63 For 2014-2018 Chevy Silverado & GMC Sierra 1500 2500 LED 3rd Brake Light Smoke USD 21.60 For 99-16 Ford Super Duty 2-Row LED Rear Third 3RD Tail Brake Light Stop Lamp USD 17.15 LED 3RD Third Brake Light Cargo Lamp Smoke For 07-13 Chevy Silverado GMC Sierra USD 17.02 Led Third 3rd Brake Light For 1999-16 Ford F250 F350 Super Duty Cargo 3D US Ship USD 21.27 Delivery New List Item 10) Round 2" Amber Side Marker Flower 9Led Light Clearance Lamp for Pickup 2Wire USD 46.29 For 2011-2017 Honda Odyssey Electric AC Condenser Cooling Fan Kit Front 12V USD 111.24 AWD For Jeep Grand Cherokee Dodge Durango 2011-2022 2 Speed Front Right CV Axle USD 82.24 For GMC 2003-2014 SAVANA 1500 Struts Absorber Left Right Kits Front Pair Shocks USD 41.29 2x Front CV Axles For Mercedes-Benz C350 2013-2015 Mercedes-Benz C300 2008-2014 USD 124.71 Help & Info Payment Policy Shipping Policy Return Policy FAQ About Us Fits 2014-2009 Nissan Murano V6 3.5L DOHC Petrol Front Driver Side CV Axle Shaft Fitment: Nissan Murano 2009-2014 Position: Front Left Package Included: 1x CV Axle The role of CV Axle They are used to transfer power from the vehicle's transmission and differential to the wheels to propel the vehicle forward. They feature lubricated, flexible joints that allow the shaft to flex according to road conditions with minimal impact on power transmission. The joints are grease lubricated and covered with rubber boots to protect them from dust and dirt. How to change CV Axle ? Step1. First, make sure you have purchased a driveshaft that matches your car model. Step2. Before starting, make sure your car's engine has cooled down and stopped running. Also, make sure your work area is tidy, spacious, and well-ventilated. Step3. Raise the car high enough off the ground so that you can easily access where the driveshaft is. This can be done by using a jack or car lift. Step4. Locate where the driveshaft is located, usually in the middle of the bottom of the car. It may have a protective cover that needs to be removed to access the driveshaft. Step5. Use a suitable tool (such as a wrench) to loosen the bolt or nut on the driveshaft and carefully remove the old driveshaft from the car. Step6. Clean the driveshaft socket and bearing housing to make sure no oil or other debris remains. Step7. Slide the new driveshaft into the socket on the underside of the car until it reaches the proper mounting position. Be careful not to push it in forcefully to avoid damaging the drive shaft or car parts. Step8. Use a wrench to tighten the bolt or nut on the drive shaft until it is fully seated. Step9. Check that the drive shaft is installed correctly and that it shows no signs of looseness or damage. Step10. Lower the vehicle back to the ground and perform a test drive to ensure the driveshaft is functioning properly. If there are any problems, please make adjustments in time. Payment Shipping Returns Feedback 1.We accept any payment which can be accepted by eBay. 2.Please do check the shipping address. If you want to change the shipping address, please contact us by eBay messages. 3.If you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement. 4.Payment must be received within 10 days as auction ended or order might be delayed. 1. Orders processed within 24 hours of payment verification. (if you want cancel orders or change address pls contact us within 6 hours after payment,or we are not responsible for shipping a replacement.) 2. The images shown are not the actual item and are for your reference only. 3. Fast shipping: All our packages use USPS First Class/UPS/Fedex... Package Service 4. If you have not received your shipment within 15 days from payment , please contact us. We will track the shipment and get back to you as soon as possible with a reply. Our goal is customer satisfaction! 1. You have 30 days to contact us and 10 days to return it from the date it was received. If this item is in your possession more than 7 days, it is considered used and we will not issue you a refund or replacement. There are NO EXCEPTIONS! 2. All returned items must be in the original packaging and you must provide us with the shipping tracking number, specific reason for the return, and item custom lable. 3. We will refund your full winning bid amount, upon receipt of the item in its original condition and packaging with all components and accessories included, AFTER both Buyer and Seller cancel the transaction from eBay. OR, you may choose to have a replacement. 4. Return shipping is to be paid by the Buyer. 1. We maintain high standards of excellence (five stars review)and strive for 100% customer satisfaction! FEEDBACK IS VERY IMPORTANT TO US. We request that you contact us immediately BEFORE you give us neutral or negative feedback, so that we can satisfactorily address your concerns. 2. It is impossible to address issues if we do not know about them! hilamps_All rights reserved.